COMPOSIZIONE CHIMICA EN 573-3
Designazione del materiale | Composizione chimica | Other elements | Al min. | ||||||||||
Simbolica | Numerica | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Note | Ciasc-uno | Totale | |
EN AW-1050A | EN AW-Al 99,5 | 0,25 | 0,40 | 0,05 | 0,05 | 0,05 | - | 0,07 | 0,05 | 99,5 | |||
EN AW-2017A | EN AW-Al CuMgSi (A) | 0,20 - 0,8 | 0,70 | 3,5 - 4,5 | 0,40 - 1,0 | 0,40 - 1,0 | 0,10 | 0,25 | 0,25 (Ti+Zr) | 0,05 | 0,15 | Resto | |
EN AW-2024 | EN AW-Al Cu4MgSi | 0,50 | 0,50 | 3,8 - 4,9 | 0,30 - 0,9 | 1,2 - 1,8 | 0,10 | 0,25 | 0,15 | ||||
EN AW-5052 | EN AW-Al Cu4Mg1 | 0,25 | 0,40 | 0,10 | 0,10 | 2,2 - 2,8 | 0,15 - 0,35 | 0,15 - 0,35 | 0,10 | 0,05 | 0,15 | Resto | |
EN AW-5754 | EN AW-Al Mg3 | 0,40 | 0,40 | 0,10 | 0,50 | 2,6 - 3,6 | 0,30 | 0,20 | 0,15 | 0,10 - 0,6 (Mn + Cr) | 0,05 | 0,15 | Resto |
EM AW-6082 | EN AW-Al Si1MgMn | 0,7 - 1,3 | 0,50 | 0,10 | 0,40 - 1,00 | 0,6 - 1,2 | 0,25 | 0,20 | 0,10 | 0,05 | 0,15 | Resto | |
EN AW-7075 | EN AW-Al Zn5,5MgCu | 0,40 | 0,50 | 1,2 - 2,0 | 0,30 | 2,1 - 2,9 | 0,18 - 0,28 | 5,1 - 6,1 | 0,2 - 0,25 (Zr+Ti) | 0,05 | 0,15 | Resto |
Equivalenze internazionali approssimative | |||||||
Designazione simbolica | Designazione numerica | EEUU (AISI) | GIAPPONE (JIS) | CINA (GB) | |||
EN AW-1050A | EN AW-Al 99,5 | ||||||
EN AW-2017A | EN AW- Al CuMgSi (A) | ||||||
EN AW-2024 | EN AW-Al Cu4MgSi | ||||||
EN AW-5052 | EN AW-Al Cu4Mg1 | ||||||
EN AW-5754 | EN AW-Al Mg3 | ||||||
EN AW-6082 | EN AW - Al Si1MgMn | ||||||
EN AW-7075 | EN AW-Al Zn5,5MgCu |
CARATTERISTICHE MECCANICHE EN 1301-2
1000 SERIES (AL)
Designation of the material | Metallurgical condition | Diameter d up to & including (mm) | Tensile strength | Yield strength Rp0.2 | Elongation | |
Rm | ||||||
MPA | MPa | A100 mm | ||||
min. | max. | typical | (typical %) | |||
O | 20 | - | 95 | - | 35 | |
EN AW-1050A [Al 99.5] | H14 | 18 | 100 | - | 95 | 5 |
H16 | 15 | 120 | - | 115 | 3 | |
H18 | 10 | 140 | - | 135 | 3 |
2000 SERIES (AL CU)
Designation of the material | Metallurgical condition | Diameter d up to & including (mm) | Tensile strength | Yield strength Rp0.2 | Elongation | |
Rm | ||||||
MPA | MPa | A100 mm | ||||
min. | max. | typical | (typical %) | |||
H13 | 18 | 210 | 300 | 190 | 5 | |
EN AW-2017A [Al Cu4MgSi(A)] | T4 | 18 | 380 | - | 255 | 18 |
H18 | 10 | 315 | - | - | - | |
H13 | 18 | 230 | 300 | 200 | 5 | |
EN AW-2024 [Al Cu4Mg1] | T4 | 18 | 420 | - | 315 | 18 |
H18 | 10 | 320 | - | - | - |
5000 SERIES (AL MN)
Designation of the material | Metallurgical condition | Diameter d up to & including (mm) | Tensile strength | Yield strength Rp0.2 | Elongation | |
Rm | ||||||
MPA | MPa | A100 mm | ||||
min. | max. | typical | (typical %) | |||
O | 20 | - | 225 | 100 | 15 | |
H14 | 18 | 225 | 275 | 225 | 4 | |
EN AW-5052 [Al Mg2.5] | H18 | 10 | 275 | - | 275 | 3 |
H32 | 18 | 190 | 240 | 145 | 11 | |
H34 | 15 | 215 | 265 | 195 | 8 | |
H38 | 10 | 260 | - | 245 | 5 | |
O | 20 | - | 250 | 110 | 16 | |
H12 | 18 | 230 | 280 | 200 | 6 | |
H14 | 18 | 255 | 305 | 250 | 3 | |
EN AW-5754 [Al Mg3] | H18 | 10 | 305 | - | 300 | 2 |
H32 | 18 | 220 | 270 | 160 | 11 | |
H34 | 15 | 245 | 295 | 210 | 8 | |
H38 | 10 | 290 | - | 260 | 4 |
6000 SERIES (AL MGSI)
Designation of the material | Metallurgical condition | Diameter d up to & including (mm) | Tensile strength | Yield strength Rp0.2 | Elongation | |
Rm | ||||||
MPA | MPa | A100 mm | ||||
min. | max. | typical | (typical %) | |||
H13 | ≤ 18 | 165 | 225 | 130 | 4 | |
H18 | ≤ 10 | 220 | - | 200 | 2 | |
T39 | ≥ 6 | 310 | - | - | - | |
EN AW-6082 [Al Si1MgMn] | T39 | < 6 | 360 | - | - | - |
T4 | ≤ 20 | 205 | 285 | 135 | 13 | |
T6 | ≤ 20 | 300 | - | 270 | 10 | |
T89 | < 6 | 340 | - | - | - |
7000 SERIES (AL ZN)
Designation of the material | Metallurgical condition | Diameter d up to & including (mm) | Tensile strength | Yield strength Rp0.2 | Elongation | |
Rm | ||||||
MPA | MPa | A100 mm | ||||
min. | max. | typical | (typical %) | |||
O | 20 | - | 275 | 110 | 13 | |
EN AW-7075 [Al Zn5.5MgCu] | H13 | 18 | 230 | 310 | 230 | 2.5 |
H18 | 10 | 285 | - | 260 | 2 | |
T6 | 20 | 510 | - | 485 | 10 |
DIMENSIONAL TOLERANCES ACCORDING TO STANDARD UNE-EN 1301-3
DIMENSIONAL TOLERANCES ROUND WIRE
Specified diameter | Tolerance | |
From | To (inclusive) | General Application |
- | 1 | ± 0.02 |
1 | 3 | ± 0.03 |
3 | 6 | ± 0.04 |
6 | 10 | ± 0.05 |
10 | 15 | ± 0.07 |
15 | 20 | ± 0.11 |
DIMENSIONAL TOLERANCES RECTANGULAR WIRE
Width or thickness | Tolerance | ||
From | To | Thickness | Width |
- | 1 | ± 0.03 | ± 0.04 |
1 | 3 | ± 0.04 | ± 0.05 |
3 | 6 | ± 0.05 | ± 0.07 |
6 | 10 | ± 0.07 | ± 0.1 |
10 | 15 | ± 0.1 | ± 0.14 |
15 | 20 | ± 0.14 | ± 0.18 |
STANDARD LENGTH TOLERANCES
NOMINAL LENGTH | TOLERANCE |
L < = 1000 mm. | +/- 1 mm. |
1000 < L < = 4000 | - 0mm. / +3 mm. |